The Effects of Modifying Agents on the Production of Bioplastic from Sago
Abstract
This study aims to develop sago starch-based bioplastics with the addition of modifying agents such as acetic acid, chitosan, and glycerin to improve mechanical properties, elongation, and biodegradability. The results showed that the optimal combination was reached at 4% acetic acid and 2% chitosan concentration, resulting in the highest tensile strength of 8 MPa, elongation at break of 26%, and degradation rate of 70%. At this condition, the bioplastic matrix has an optimal balance between strength, flexibility, and degradability. Increasing the acetic acid concentration to 6% caused a decrease in tensile strength to 4.2 MPa and elongation at break to 14%, indicating degradation of the matrix structure due to excess acid. Chitosan also affected the mechanical properties, where increasing its concentration from 2% to 4% tended to decrease the elongation at break. The degradation rate tended to increase with higher concentrations of acetic acid, reaching 82% at 6% acetic acid concentration with 2% chitosan, while higher concentrations of chitosan (4%) slowed down the degradation due to a denser and stronger matrix structure. Overall, the combination of sago starch, acetic acid, chitosan, and glycerin produced bioplastics that have improved mechanical properties, water resistance, and environmental friendliness, making them a potential alternative to replace conventional plastics in various industrial applications. These findings support the development of environmentally friendly materials that can reduce the negative impacts to the environment in general and in Papua as the local producer of Sago.
Full Text:
PDFReferences
D. Rozanna, B. Novi Sylvia, C. Zulnazri, S. D. Januar Parlaungan, and F. Medyan Riza, “Characterization of Sago Starch Based Degradable Plastic with Calcium Carbonate (CaCO₃) as Filler,” J. Innov. Technol., vol. 2023, no. 11, pp. 1–11, 2023. [Online]. Available: https://www.aimspress.com/article/doi/10.3934/environsci.2024014?viewType=HTML
B. Sulaeman, N. Salam, A. E. Eka Putra, and L. H. Arma, “Development of bioplastics from Tawaro’s environmentally friendly sago starch (Metroxylon),” East.-Eur. J. Enterp. Technol., vol. 125, no. 12, 2023. doi: 10.15587/1729-4061.2023.289626.
Y. O. Ansanay, D. Y. Runtuboi, and E. T. Wiradyo, “Potency of utilizing sago starch as natural resource from Papua in the production of biodegradable plastic,” Int. J. Adv. Sci. Eng. Inf. Technol., vol. 12, no. 1, pp. 353–358, 2022. doi: https://ijaseit.insightsociety.org/index.php/ijaseit/article/view/14267
A. Shafqat, A. Tahir, A. Mahmood, A. B. Tabinda, A. Yasar, and A. Pugazhendhi, “A review on environmental significance carbon footprints of starch-based bio-plastic: A substitute of conventional plastics,” Biocatal. Agric. Biotechnol., vol. 27, p. 101540, 2020. doi: 10.1016/j.bcab.2020.101540.
A. R. Fauziah, M. Lanuru, M. Syahrul, S. Werorilangi, and E. B. Demmallino, “Utilization of solid waste from sago flour industry (sago pith waste) as biodegradable plastic,” Adv. Environ. Biol., vol. 14, no. 1, pp. 42–48, 2020.doi https://www.aensiweb.net/AENSIWEB/aeb/aeb/2020/January/42-47(7).pdf
S. Guleria, H. Singh, A. Jain, S. K. Arya, S. Puri, and M. Khatri, “Response surface methodology-based preparation of sago starch bioplastic film for food packaging,” Int. J. Polym. Anal. Charact., vol. 29, no. 7, pp. 478–495, 2024. doi: 10.1080/1023666X.2024.2383480.
B. Sulaeman, N. Salam, A. E. E. Putra, and L. H. Arma, “Microstructural and mechanical properties of sago starch bioplastics (Metroxylon sp) as biodegradable plastics,” in AIP Conf. Proc., vol. 3115, no. 1, 2024. doi: 10.1063/5.0207246.
A. Awadhiya, D. Kumar, and V. Verma, “Crosslinking of agarose bioplastic using citric acid,” Carbohydr. Polym., vol. 151, pp. 60–67, 2016. doi: 10.1016/j.carbpol.2016.05.040.
D. Amalia, D. Saleh, and E. Djonaedi, “Synthesis of biodegradable plastics using corn starch and corn husk as the fillers as well as chitosan and sorbitol,” in J. Phys.: Conf. Ser., vol. 1442, no. 1, p. 012007, 2020, IOP Publishing. [Online]. Available: https://iopscience.iop.org/article/10.1088/1742-6596/1442/1/012007/meta.
S. W. Lusiana, D. Putri, and I. Z. Nurazizah, “Bioplastic properties of sago-PVA starch with glycerol and sorbitol plasticizers,” in J. Phys.: Conf. Ser., vol. 1351, no. 1, p. 012102, 2019, IOP Publishing. [Online]. Available: https://iopscience.iop.org/article/10.1088/1742-6596/1351/1/012102/meta.
A. Folino, A. Karageorgiou, P. S. Calabrò, and D. Komilis, “Biodegradation of wasted bioplastics in natural and industrial environments: A review,” Sustainability, vol. 12, no. 15, p. 6030, 2020. [Online]. Available: https://www.mdpi.com/2071-1050/12/15/6030.
Y. Zoungranan, E. Lynda, K. K. Dobi-Brice, E. Tchirioua, C. Bakary, and D. D. Yannick, “Influence of natural factors on the biodegradation of simple and composite bioplastics based on cassava starch and corn starch,” J. Environ. Chem. Eng., vol. 8, no. 5, p. 104396, 2020. doi: 10.1016/j.jece.2020.104396.
A. B. D. Nandiyanto, M. Fiandini, R. Ragadhita, A. Sukmafitri, H. Salam, and F. Triawan, “Mechanical and biodegradation properties of cornstarch-based bioplastic material,” Mater. Phys. Mech., vol. 44, no. 3, 2020. [Online]. Available: https://www.ipme.ru/e-journals/MPM/no_34420/MPM344_09_nandiyanto.pdf.
F. Wu, Z. Zhou, M. Liang, L. Zhong, and F. Xie, “Ultrasonication improves the structures and physicochemical properties of cassava starch films containing acetic acid,” Starch-Stärke, vol. 73, no. 1–2, p. 2000094, 2021. doi: 10.1002/star.202000094.
M. Lintang, O. Tandi, P. Layuk, S. Karouw, and A. Dirpan, “Characterization edible films of sago with glycerol as a plasticizer,” in IOP Conf. Ser.: Earth Environ. Sci., vol. 807, no. 2, p. 022070, 2021, IOP Publishing. [Online]. Available: https://iopscience.iop.org/article/10.1088/1755-1315/807/2/022070/meta.
S. X. Tan et al., “Characterization and parametric study on mechanical properties enhancement in biodegradable chitosan-reinforced starch-based bioplastic film,” Polymers, vol. 14, no. 2, p. 278, 2022. [Online]. Available: https://www.mdpi.com/2073-4360/14/2/278.
E. Maneking, H. F. Sangian, and S. H. J. Tongkukut, “Pembuatan dan karakterisasi bioplastik berbahan dasar biomassa dengan plasticizer gliserol,” J. MIPA, vol. 9, no. 1, pp. 23–27, 2020. [Online]. Available: https://ejournal.unsrat.ac.id/v3/index.php/jmuo/article/view/27420/26972.
A. Widhiantari and G. N. De Side, “Optimization of physical characteristics of bioplastics from agricultural waste using response surface methodology (RSM),” IOP Conf. Ser.: Earth Environ. Sci., vol. 913, no. 1, p. 012001, 2021. doi: https://iopscience.iop.org/article/10.1088/1755-1315/913/1/012055/meta
A. S. Rusdianto, W. Amilia, A. L. Pratiwi, and H. Adila, “Biodegradable spoon based on glycerol and cassava starch with the addition of sugar cane pulp,” Int. J. Food Agric. Nat. Resour., vol. 4, no. 3, pp. 58–61, Sep. 2023. https://journal.fanres.org/index.php/IJFANRES/article/view/167
A. S. Rusdianto, M. Usman, T. Lindriati, E. Ruriani, and N. S. Mahardika, “The characterization of biodegradable plastics from cassava starch with varied addition of robusta coffee skin (Coffea canephora) and glycerol,” Int. J. Food Agric. Nat. Resour., vol. 3, no. 3, pp. 34–38, Dec. 2022. https://journal.fanres.org/index.php/IJFANRES/article/viewFile/68/74
D. Dordevic, L. Necasova, B. Antonic, S. Jancikova, and B. Tremlová, “Plastic cutlery alternative: Case study with biodegradable spoons,” Foods, vol. 10, no. 7, 2021. https://www.mdpi.com/2304-8158/10/7/1612
M. T. Hossain et al., “Cellulose and starch-based bioplastics: a review of advances and challenges for sustainability,” Polym.-Plast. Technol. Mater., vol. 63, no. 10, pp. 1329–1349, 2024. doi: https://doi.org/10.1080/25740881.2024.2329980.
DOI: https://doi.org/10.46676/ij-fanres.v6i1.443
Refbacks
- There are currently no refbacks.
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.